In-Use Motor Vehicle Recall and Correction Regulation Article 6
Prior to perform the preliminary investigation test or confirmation investigation test by the central competent authority, the vehicle manufacturer or importer shall send personnel to cooperate with execution of inspection, restoration and maintenance on the test vehicles. The manufacturer or importer that fails to send personnel shall not raise objection to the results of inspection, restoration and maintenance on test vehicles.The inspection and restoration maintenance as mentioned in previous paragraph shall comply with the following stipulations:6.1. The identification numbers of all components of emission control systems shall be consistent with information recorded in the vehicle model’s Certificate of Conformity issued by the central competent authority.6.2. Tires, battery, belts, fluid levels, radiator cap, vacuum tubing, flexible tubing and emission control systems related interconnect lines and hoses shall be fully intact.6.3. Fuel supply and emission control system components shall not be replaced, modified or inappropriately adjusted.6.4. Cylinder pressure shall meet the original design standards.6.5. Engine parameters shall be adjusted to the original design and manufacture specifications.6.6. Replace the fuel with test fuel.The previous paragraph mentioned inspection and restoration maintenance results shall be recorded; if the inspection fails to meet stipulation requirements, with consent of the central competent authority, the vehicle may be excluded from the list of recall and correction test vehicles.Within 800 kilometers travel mileage for the test vehicle, any scheduled periodical maintenance shall be performed. If necessary, the vehicle manufacturer or importer may perform the next stage periodical maintenance.
中文原文 使用中汽車召回改正辦法第6條
中央主管相關進行初步調查測試或確認調查測試前，汽車製造者或進口商應派員會同對受測汽車進行各項檢查及恢復保養；未派員會同者，汽車製造者或進口商不得對受測汽車之檢查及恢復保養結果提出異議。
前項檢查及恢復保養應符合下列規定：
一、污染排放控制系統各元件辨識號碼應與中央主管機關申請核發之汽車車型排氣審驗合格證明所附資料相符。
二、輪胎、電瓶、皮帶、液面高度、水箱蓋、真空管、軟管及與污染排放控制系統有關之線路完整。
三、供油及污染排放控制系統元件相關項目不可更換、改裝或不當調整。
四、汽缸壓力符合原廠設計規範。
五、引擎各參數調整至原設計製造之規格。
六、使用燃料更換為測試用燃料。
前項檢查及恢復保養結果應作成紀錄；檢查不符合規定者，經中央主管機關同意，得不列為召回改正調查測試之受測汽車。
受測汽車行駛里程在任一規定定期保養里程八百公里內，應進行該項定期保養；必要時，汽車製造者或進口商得進行下一階段定期保養。
前項檢查及恢復保養應符合下列規定：
一、污染排放控制系統各元件辨識號碼應與中央主管機關申請核發之汽車車型排氣審驗合格證明所附資料相符。
二、輪胎、電瓶、皮帶、液面高度、水箱蓋、真空管、軟管及與污染排放控制系統有關之線路完整。
三、供油及污染排放控制系統元件相關項目不可更換、改裝或不當調整。
四、汽缸壓力符合原廠設計規範。
五、引擎各參數調整至原設計製造之規格。
六、使用燃料更換為測試用燃料。
前項檢查及恢復保養結果應作成紀錄；檢查不符合規定者，經中央主管機關同意，得不列為召回改正調查測試之受測汽車。
受測汽車行駛里程在任一規定定期保養里程八百公里內，應進行該項定期保養；必要時，汽車製造者或進口商得進行下一階段定期保養。