Regulations Governing the Application for Prior Release of Mechanical Products Article 2
The obligatory applicants who import mechanical products that are subject to the type certification required by Article 8 of the Act may apply to the central competent authority for prior release of their products and present a letter of attestation:1. Products that pass type certification, but the qualification labels have not attached in accordance with related requirements;2. Products of which the applications for type certification have been made, but the certificates of type certification have not yet been issued;3. Products that pass type certification and are not assembled;4. Products that are separated or partly separated components and pass type certification;5. Other situations where prior release is necessary and approved by the central competent authority.Permission for a prior release issued in accordance with subparagraph 2 of the preceding paragraph shall be limited to one time only for each obligatory applicant with the same product, except for applications under one of the following conditions approved by the central competent authority.1. The number of samples to be tested that have been permitted for prior release is insufficient, so that the type certification cannot be completed.2. Products that have been permitted for prior release are not identified as type representative, which makes it difficult to perform type certification.In accordance with the proviso of the preceding paragraph, the obligatory applicants should apply to the central competent authority for prior release of their products before the expiration of the approval period for the original application, and attach the explanatory document that is issued by the body performing the type certification. The application is limited to one time, and the approval period is subject to the period for the original application.
中文原文 機械類產品申請先行放行辦法第2條
報驗義務人輸入本法第八條所定應實施型式驗證之機械類產品，有下列情形之一者，得向中央主管機關具結，申請先行放行：
一、經型式驗證合格之產品，尚未依法張貼合格標章。
二、已申請型式驗證之產品，尚未取得型式驗證合格證明書。
三、經型式驗證合格之產品，其為未組裝完成品。
四、經型式驗證合格之產品，其為全拆散或半拆散之零組件。
五、其他有先行放行之必要，報經中央主管機關核准。
依前項第二款規定申請先行放行者，對同一報驗義務人之同一型式產品，以核准一次為限。
但有下列情形之一，經中央主管機關核准者，不以一次為限：
一、經核准先行放行之待測產品數量不足，致無法完成型式驗證。
二、經核准先行放行之產品未具型式代表性，致執行型式驗證有困難。
報驗義務人依前項但書規定申請先行放行者，應於原申請案之核准期限屆滿前，檢附受理型式驗證機構出具之說明文件為之，並以一次為限；其核准期限，以原申請案之期限為準。
一、經型式驗證合格之產品，尚未依法張貼合格標章。
二、已申請型式驗證之產品，尚未取得型式驗證合格證明書。
三、經型式驗證合格之產品，其為未組裝完成品。
四、經型式驗證合格之產品，其為全拆散或半拆散之零組件。
五、其他有先行放行之必要，報經中央主管機關核准。
依前項第二款規定申請先行放行者，對同一報驗義務人之同一型式產品，以核准一次為限。
但有下列情形之一，經中央主管機關核准者，不以一次為限：
一、經核准先行放行之待測產品數量不足，致無法完成型式驗證。
二、經核准先行放行之產品未具型式代表性，致執行型式驗證有困難。
報驗義務人依前項但書規定申請先行放行者，應於原申請案之核准期限屆滿前，檢附受理型式驗證機構出具之說明文件為之，並以一次為限；其核准期限，以原申請案之期限為準。