Regulations Governing the Certification for Aviation Products, Appliances and Parts Article 10
Each applicant must allow CAA to make any inspection and, upon request by CAA, make any inspection, flight and ground test necessary to determine compliance with the applicable requirements. Each applicant must carry on all necessary inspections and tests necessary to ensure that--5) The product concerned complies with the applicable airworthiness, aircraft noise, fuel venting, and exhaust emission requirements;6) Materials and products conform to the specifications in the type design;7) Parts of the products conform to the drawings in the type design; and8) The manufacturing processes, construction and assembly conform to those specified in the type design.Except as approved by CAA, the applicant should submit to CAA a statement, certifying that the requirements stipulated in subparagraph (2)~(4) of the first paragraph of this Article have been complied with, prior to his/her submission to CAA for inspection or conduct any flight test or ground test requested by CAA,Except as approved by CAA, no change may be made to an aircraft product between the time that compliance with subparagraph (2)~(4) of the first paragraph of this Article is shown for that aircraft product and the time that it is presented to the CAA for test.The type design, as cited in the first paragraph of this Article, consists of1) The drawings and specifications, and a listing of those drawings and specifications, necessary to define the configuration and the design features of the product shown to comply with the requirements applicable to the product;2) Information on dimensions, materials, and processes necessary to define the structural strength of the product;3) The Airworthiness Limitations section of the Instructions for Continued Airworthiness as required by applicable airworthiness standards;4) Any other data necessary to allow, by comparison, the determination of the airworthiness, noise characteristics, fuel venting, and exhaust emissions (where applicable) of later products of the same type.
中文原文 航空產品與其各項裝備及零組件適航檢定管理規則第10條
申請型別檢定應接受民航局之檢查與依民航局要求進行檢驗、飛行試驗及地面試驗。
申請人應完成各項必要之檢驗及試驗，確認符合下列規定：
一、符合相關之適航標準與其他法規對航空器之噪音、燃油及廢氣之排放規定。
二、材料及產品符合型別設計之技術規範。
三、產品之零組件符合型別設計之設計圖。
四、製程、建造及裝配符合型別設計之規定。
航空產品於提交民航局檢查或進行民航局要求之試驗前，申請人應聲明符合前項第二款至第四款之規定。
但經民航局核准者，不在此限。
航空產品於民航局進行第一項第二款至第四款符合性檢查後，至進行民航局要求之試驗期間，申請人不得對其為任何變更。
但經民航局核准者，不在此限。
第一項型別設計係指下列事項：
一、為確認產品構型及設計特性符合相關適航標準所需之設計圖、技術規範及其清單。
二、為界定產品結構強度所需之尺寸、材料及製程資料。
三、依照相關適航標準之要求，所訂持續適航之適航限制。
四、為判定同一型別後期產品之適航性、噪音與燃油及廢氣排放等特性，所提供可供比對之必要資料。
申請人應完成各項必要之檢驗及試驗，確認符合下列規定：
一、符合相關之適航標準與其他法規對航空器之噪音、燃油及廢氣之排放規定。
二、材料及產品符合型別設計之技術規範。
三、產品之零組件符合型別設計之設計圖。
四、製程、建造及裝配符合型別設計之規定。
航空產品於提交民航局檢查或進行民航局要求之試驗前，申請人應聲明符合前項第二款至第四款之規定。
但經民航局核准者，不在此限。
航空產品於民航局進行第一項第二款至第四款符合性檢查後，至進行民航局要求之試驗期間，申請人不得對其為任何變更。
但經民航局核准者，不在此限。
第一項型別設計係指下列事項：
一、為確認產品構型及設計特性符合相關適航標準所需之設計圖、技術規範及其清單。
二、為界定產品結構強度所需之尺寸、材料及製程資料。
三、依照相關適航標準之要求，所訂持續適航之適航限制。
四、為判定同一型別後期產品之適航性、噪音與燃油及廢氣排放等特性，所提供可供比對之必要資料。